Sheath Making Supplies and Leatherworking Tools

Online Catalogue | For tool making supplies | 

Sheath Making Supplies and Leatherworking Tools

Page:  1  2  3  4  5  ...   >   >>   View All (230)
Western Sheath blanks 95 1580

Western Sheath blanks 95

1580


Price: 9.00 (Including VAT at 20%)

Quantity:

Fits for blades 90-100 mm. Needs to be sewn up, gluing is possible but not as permanent.

Sheaths blanks are made from good quality 2.5mm leather with a welt to protect the stitching area, then dyed dark brown.

TIP: Soak blank in Warm water for about three minutes, sew up, then wrap your knfe in cling film and gently work into the sheath, this will stretch the leather slightly and help with the fit. Leave knife in sheath for a couple of hours remove and allow to dry fully. Treat with some bees wax and your knife will fit like a glove!!

Fits for blades 90-100 mm.

More...


Sheath Blank Kit 1 EHK-SK1

Sheath Blank Kit 1

EHK-SK1


Price: 10.00 (Including VAT at 20%)

Quantity:



Fits blades 100-110 mm.

The kit consists of a pre-marked 3mm Veg tanned leather blank with stitching holes defined and the inside has been prepared to help with the folding of the leather.

A belt loop is also supplied with two rivets that enables the user to decide if left or right-handed use if required.

Some basic instructions:

1. Rivet the belt loop in the desired position.

2. Enlarge the pin pricks with an awl to allow the needles to pass through easily.

3. Soak the sheath in some warm water for about 5 minutes.
This will make the leather very soft and supple.

4. Start sowing from the tip when you reach the top sew back a few stitches to hold it all tight.

5. Wrap your knife in cling film and gently work the knife into the sheath.
Then work with you fingers to mould the leather to take on the shape of your handle.

6. You can leave the leather in it's natural state. It will take on a patina that will darken with time, or
alternatively it can be dyed at this stage, but it's advisable to take the knife out before doing so.
Whatever you decide to do, the knife should only be left in the damp sheath for a couple of hours, then take it out carefully and if you can hang it in a warm place to harden.

These instructions will be included with your kit



More...


Sheath Blank Kit 2 EHK-SK2

Sheath Blank Kit 2

EHK-SK2


Price: 10.00 (Including VAT at 20%)

Quantity:



Fits blades 90-95mm. Trapper 95 with tapered scales

The kit consists of a pre-marked 3mm Veg tanned leather blank with stitching holes defined and the inside has been prepared to help with the folding of the leather.

A belt loop is also supplied with two rivets that enables the user to decide if left or right-handed use if required.

Some basic instructions:

1. Rivet the belt loop in the desired position.

2. Enlarge the pin pricks with an awl to allow the needles to pass through easily.

3. Soak the sheath in some warm water for about 5 minutes.
This will make the leather very soft and supple.

4. Start sowing from the tip when you reach the top sew back a few stitches to hold it all tight.

5. Wrap your knife in cling film and gently work the knife into the sheath.
Then work with you fingers to mould the leather to take on the shape of your handle.

6. You can leave the leather in it's natural state. It will take on a patina that will darken with time, or
alternatively it can be dyed at this stage, but it's advisable to take the knife out before doing so.
Whatever you decide to do, the knife should only be left in the damp sheath for a couple of hours, then take it out carefully and if you can hang it in a warm place to harden.

These instructions will be included with your kit



More...


Sheath Blank Kit 3 EHK-SK3

Sheath Blank Kit 3

EHK-SK3


Price: 10.00 (Including VAT at 20%)

Quantity:



Fits blades 110-120mm.x 20mm

The kit consists of a pre-marked 3mm Veg tanned leather blank with stitching holes defined and the inside has been prepared to help with the folding of the leather.

A belt loop is also supplied with two rivets that enables the user to decide if left or right-handed use if required.

Some basic instructions:

1. Rivet the belt loop in the desired position.

2. Enlarge the pin pricks with an awl to allow the needles to pass through easily.

3. Soak the sheath in some warm water for about 5 minutes.
This will make the leather very soft and supple.

4. Start sowing from the tip when you reach the top sew back a few stitches to hold it all tight.

5. Wrap your knife in cling film and gently work the knife into the sheath.
Then work with you fingers to mould the leather to take on the shape of your handle.

6. You can leave the leather in it's natural state. It will take on a patina that will darken with time, or
alternatively it can be dyed at this stage, but it's advisable to take the knife out before doing so.
Whatever you decide to do, the knife should only be left in the damp sheath for a couple of hours, then take it out carefully and if you can hang it in a warm place to harden.

These instructions will be included with your kit



More...


Sheath Blank Kit 4 EHK-SK4

Sheath Blank Kit 4

EHK-SK4


Price: 10.00 (Including VAT at 20%)

Quantity:



Fits blades 95mm.x 20mm Polar 95

The kit consists of a pre-marked 3mm Veg tanned leather blank with stitching holes defined and the inside has been prepared to help with the folding of the leather.

A belt loop is also supplied with two rivets that enables the user to decide if left or right-handed use if required.

Some basic instructions:

1. Rivet the belt loop in the desired position.

2. Enlarge the pin pricks with an awl to allow the needles to pass through easily.

3. Soak the sheath in some warm water for about 5 minutes.
This will make the leather very soft and supple.

4. Start sowing from the tip when you reach the top sew back a few stitches to hold it all tight.

5. Wrap your knife in cling film and gently work the knife into the sheath.
Then work with you fingers to mould the leather to take on the shape of your handle.

6. You can leave the leather in it's natural state. It will take on a patina that will darken with time, or
alternatively it can be dyed at this stage, but it's advisable to take the knife out before doing so.
Whatever you decide to do, the knife should only be left in the damp sheath for a couple of hours, then take it out carefully and if you can hang it in a warm place to harden.

These instructions will be included with your kit



More...


Sheath Blank Kit 5 EHK-SK5

Sheath Blank Kit 5

EHK-SK5


Price: 10.00 (Including VAT at 20%)

Quantity:



Fits blades 90mm.x 27mm Bushman

The kit consists of a pre-marked 3mm Veg tanned leather blank with stitching holes defined and the inside has been prepared to help with the folding of the leather.

A belt loop is also supplied with two rivets that enables the user to decide if left or right-handed use if required.

Some basic instructions:

1. Rivet the belt loop in the desired position.

2. Enlarge the pin pricks with an awl to allow the needles to pass through easily.

3. Soak the sheath in some warm water for about 5 minutes.
This will make the leather very soft and supple.

4. Start sowing from the tip when you reach the top sew back a few stitches to hold it all tight.

5. Wrap your knife in cling film and gently work the knife into the sheath.
Then work with you fingers to mould the leather to take on the shape of your handle.

6. You can leave the leather in it's natural state. It will take on a patina that will darken with time, or
alternatively it can be dyed at this stage, but it's advisable to take the knife out before doing so.
Whatever you decide to do, the knife should only be left in the damp sheath for a couple of hours, then take it out carefully and if you can hang it in a warm place to harden.

These instructions will be included with your kit



More...


Sheath Shape Cutting Service EHK-Special

Sheath Shape Cutting Service

EHK-Special


Price: 13.00 (Including VAT at 20%)

Quantity:

FOR WESTERN STYLE SHEATHS ONLY

1. First buy your sheath of leather from us

2. Email an outline or picture of your knife along with the length of the blade and thickness of your handle.

3. Specify if you want stitch marks.

Please allow 5 working days for this service

Snap Setter 3899

Snap Setter

3899


Price: 12.00 (Including VAT at 20%)

Quantity:



Snap Setter Kit for 1/4 Eyelets 3769

Snap Setter Kit for 1/4 Eyelets

3769


Price: 12.00 (Including VAT at 20%)

Quantity:




People who bought this item also bought:

1.

Kydex Rivets 8mm

3778

Snap Setter Kit for 1/8 Eyelets 3768

Snap Setter Kit for 1/8 Eyelets

3768


Price: 10.00 (Including VAT at 20%)

Quantity:



Snap Setter Kit 8108-10

Snap Setter Kit

8108-10


Price: 21.00 (Including VAT at 20%)

Quantity:

Six piece snap setter kit for glove snaps, multi-purpose snaps (Line 16/Segma), Line 20 and Line 24 snaps

Snap Setter and Anvil 8057-00

Snap Setter and Anvil

8057-00


Price: 8.00 (Including VAT at 20%)

Quantity:

A single Punch and Anvil suitable for Medium (12mm) Snaps when working with 2.5-3mm veg tanned leather.

More...


Page:  1  2  3  4  5  ...   >   >>   View All (230)

Online Catalogue | For tool making supplies | 

Sheath Making Supplies and Leatherworking Tools

Buy now with PayPal